CAT-SET

DRILLING | T-A® Replaceable Insert Drilling System

1 Series: 17.53 mm - 24.40 mm (0.6900" - 0.9609")

T-A® Drill Holders

A30

Stub Length

Imperial Flange Shank Holders

Body

Shank

L 2

L 4

L 3

L 1

L 5

D 2

P 1

Flute

Series

Length

Part No.

21010S-100F 22010S-100F 23010S-100F 24010S-100F 25010S-100F 21015S-100F 22015S-100F 23015S-100F 24015S-100F 25015S-100F 23010H-100F 24010H-100F 24510H-100F 25010H-100F 26010H-100F 23015H-100F 24015H-100F 25015H-100F

Stub Short

1.992 2.984 3.124 5.264 2.280 1 1/8 NPT 2.643 4.219 4.359 6.499 2.280 1 1/8 NPT

Intermediate 4.518 6.094 6.234 8.374 2.280 1 1/8 NPT Standard 6.518 8.094 8.234 10.374 2.280 1 1/8 NPT Extended 10.518 12.094 12.234 14.374 2.280 1 1/8 NPT

1

Stub Short

2.554 3.484 3.624 5.764 2.280 1 1/8 NPT 2.607 4.219 4.359 6.499 2.280 1 1/8 NPT

Straight

Intermediate 4.482 6.094 6.234 8.374 2.280 1 1/8 NPT Standard 6.482 8.094 8.234 10.374 2.280 1 1/8 NPT Extended 10.482 12.094 12.234 14.374 2.280 1 1/8 NPT Intermediate 5.229 6.094 6.234 8.374 2.280 1 1/8 NPT Standard 7.229 8.094 8.234 10.374 2.280 1 1/8 NPT Standard Plus 9.226 10.091 10.231 12.371 2.280 1 1/8 NPT Extended 11.229 12.094 12.234 14.374 2.280 1 1/8 NPT Intermediate 5.291 6.094 6.234 8.374 2.280 1 1/8 NPT Standard 7.291 8.094 8.234 10.374 2.280 1 1/8 NPT Extended 11.291 12.094 12.234 14.374 2.280 1 1/8 NPT Long 14.974 15.839 15.979 18.119 2.280 1 1/8 NPT

1.5

1

Helical

1.5

NOTE: Stub length holders have a 3.175 mm (1/8") side pipe tap (P 2 ). NOTE: 1.5 series inserts fit into both 1 and 1.5 series holders. However, 1 series inserts ONLY fit into 1 series holders. See page A30: 7 for visual.

ConnecƟon Accessories

Nylon Locking Screws 7375N-IP9-1

Preset Torque Hand Driver

Admissible Tightening Torque* 305 N-cm (27.0 in-lbs) 305 N-cm (27.0 in-lbs)

Series

Insert Screws

Insert Driver

Replacement Tips

1

7375-IP9-1 739-IP9-1

8IP-9 8IP-9

8IP-9TL 8IP-9TL

8IP-9B 8IP-9B

1.5

739N-IP9-1

*Tightening torques are calculated with a fricƟon coefficient of µ = 0.14 and develop 90% of ulƟmate yield strength.

Refer to Speed and Feed charts for recommended adjustments to speeds and feeds. Refer to page A30: 146 for deep hole drilling guidelines in this secƟon of the catalog. Visit www.alliedmachine.com/DeepHoleGuidelines for the most up-to-date informaƟon and procedures. Factory technical assistance is available for your specific applicaƟons through our ApplicaƟon Engineering department : appeng@alliedmachine.com . WARNING

A30: 113 - 139

A30: 47 - 54

A30: 60 & 112

Key on A30: 2

Screws sold in mulƟples of 10. = Metric (mm) = Imperial (in)

www.alliedmachine.com | 1.330.343.4283

A30: 56