TG_SFC_US-EN

DRILLING | T-A® Replaceable Insert Drilling System

XTP TAP TAS HPU APX 4TX REV OPN SSD ACP BTA WHL CRT ALV BRN THM T-A®: Recommended Drilling Data | Imperial (inch) HSS Inserts ISO Material Hardness (BHN) HSS Grade P Free-Machining Steel 100 - 150 HSS 1118, 1215, 12L14, etc. 150 - 200 HSS 200 - 250 HSS Low-Carbon Steel 85 - 125 HSS 1010, 1020, 1025, 1522, 1144, etc. 125 - 175 HSS 175 - 225 HSS 225 - 275 HSS Medium-Carbon Steel 125 - 175 HSS 1030, 1040, 1050, 1527, 1140, 1151, etc. 175 - 225 HSS 225 - 275 HSS 275 - 325 SC, PC Alloy Steel 125 - 175 HSS 4140, 5140, 8640, etc. 175 - 225 HSS 225 - 275 HSS 275 - 325 SC, PC 325 - 375 SC, PC High-Strength Alloy 225 - 300 SC, PC 4340, 4330V, 300M, etc. 300 - 350 SC, PC 350 - 400 PC Structural Steel 100 - 150 HSS A36, A285, A516, etc. 150 - 250 HSS 250 - 350 SC, PC Tool Steel 150 - 200 SC H-13, H-21, A-4, 0-2, S-3, etc. 200 - 250 SC, PC S High-Temp Alloy 140 - 220 SC, PC Hastelloy B, Inconel 600, etc. 220 - 310 PC Titanium Alloy 140 - 220 SC, PC 220 - 310 PC Aerospace Alloy 185 - 275 SC, PC S82 275 - 350 SC, PC M Stainless Steel 400 Series 185 - 275 SC, PC 416, 420, etc. 275 - 350 SC, PC Stainless Steel 300 Series 135 - 185 SC, PC 304, 316, 17-4PH, etc. 185 - 275 SC, PC Super Duplex Stainless Steel 135 - 185 SC, PC 185 - 275 SC, PC H Wear Plate 400 SC, PC Hardox®, AR400, T-1, etc. 500 PC 600 N/A Hardened Steel 300 - 400 PC 400 - 500 PC K Nodular, Grey, Ductile Cast Iron 120 - 150 HSS 150 - 200 HSS 200 - 220 HSS 220 - 260 SC, PC 260 - 320 SC, PC N Cast Aluminum 30 HSS 180 HSS Wrought Aluminum 30 HSS 180 HSS Aluminum Bronze 100 - 200 SC 200 - 250 SC Brass 100 HSS Copper 60 SC

SFM

Feed Rate (IPR) by Diameter

3/8" - 1/2" 0.007 0.007 0.006

33/64" - 11/16"

TiN 200 180 160 170 160 150 140 160 150 140 130 150 140 130 120 110

TiAlN

TiCN

280 260 240 250 240 225 210 240 225 210 195 210 195 180 170 155 110 200 170 140 110 85 70

260 235 210 220 210 195 180 210 195 180 170 195 180 170 155 145 100 180 155 130 105 80 65

0.010 0.010 0.010 0.009 0.009 0.008 0.008 0.009 0.008 0.008 0.007 0.008 0.008 0.007 0.006 0.006 0.007 0.007 0.006 0.010 0.009 0.008 0.006 0.006 0.007 0.006 0.007 0.006 0.008 0.007 0.010 0.009 0.007 0.006 0.005 0.005 0.006 0.005 0.006 0.005 0.012 0.011 0.009 0.007 0.006 0.013 0.013 0.006 0.013 0.011 0.007 0.012 0.003 -

0.006 0.006 0.005 0.005

0.006 0.005 0.005 0.004 0.006 0.005 0.005 0.004 0.003

80 60 50

0.005 0.004 0.003 0.006 0.005 0.003 0.003 0.003 0.003 0.003 0.006 0.005

140 120 100

80 60 30 25 35 30 75 60 75 60 75 60 60 50 45 35 50 35 -

0.004 0.004

90

85

40 35 50 45

35 30 45 35 95 80 95 80 95 80 70 60 55 40 70 40 -

105

90

105

0.009 0.008 0.007 0.006 0.005 0.004

90

105

90 80 65 70 45 95 45 -

0.003 0.002 0.003 0.002 -

170 150 130 110 600 300 600 300 170 130 300 130 90

250 225 195 165 135 850 450 850 450 250 190 445 165

220 195 170 145 120 750 400 750 400 220 170 400 150

0.007 0.006 0.006 0.005 0.004 0.008 0.008 0.004 0.008 0.006 0.005 0.007

0.002

Contact our Application Engineering department for assistance when machining these materials

IMPORTANT: The speeds and feeds listed above are a general starting point for all applications. Refer to the Coolant Recommendation charts for coolant requirements to run at the recommended speeds and feeds. Factory technical assistance is available through our Application Engineering department. See adjustment examples on the following page.

40

www.alliedmachine.com | 1.330.343.4283