TG_SFC_US-EN

DRILLING | T-A® Replaceable Insert Drilling System

XTP TAP TAS HPU APX 4TX REV OPN SSD ACP BTA WHL CRT ALV BRN THM T-A®: Recommended Drilling Data | Imperial (inch) HSS Inserts | Flat Bottom Geometry ISO Material Hardness (BHN) HSS Grade P Free-Machining Steel 100 - 150 HSS 1118, 1215, 12L14, etc. 150 - 200 HSS 200 - 250 HSS Low-Carbon Steel 85 - 125 HSS 1010, 1020, 1025, 1522, 1144, etc. 125 - 175 HSS 175 - 225 HSS 225 - 275 HSS Medium-Carbon Steel 125 - 175 HSS 1030, 1040, 1050, 1527, 1140, 1151, etc. 175 - 225 HSS 225 - 275 HSS 275 - 325 SC Alloy Steel 125 - 175 HSS 4140, 5140, 8640, etc. 175 - 225 HSS 225 - 275 HSS 275 - 325 SC 325 - 375 SC High-Strength Alloy 225 - 300 SC 4340, 4330V, 300M, etc. 300 - 350 SC 350 - 400 SC Structural Steel 100 - 150 HSS A36, A285, A516, etc. 150 - 250 HSS 250 - 350 SC Tool Steel 150 - 200 SC H-13, H-21, A-4, 0-2, S-3, etc. 200 - 250 SC S High-Temp Alloy 140 - 220 SC Hastelloy B, Inconel 600, etc. 220 - 310 SC Titanium Alloy 140 - 220 SC 220 - 310 SC Aerospace Alloy 185 - 275 SC S82 275 - 350 SC M Stainless Steel 400 Series 185 - 275 SC 416, 420, etc. 275 - 350 SC Stainless Steel 300 Series 135 - 185 SC 304, 316, 17-4PH, etc. 185 - 275 SC Super Duplex Stainless Steel 135 - 185 SC 185 - 275 SC H Wear Plate 400 SC Hardox®, AR400, T-1, etc. 500 SC 600 N/A Hardened Steel 300 - 400 SC 400 - 500 SC K Nodular, Grey, Ductile Cast Iron 120 - 150 HSS 150 - 200 HSS 200 - 220 HSS 220 - 260 SC 260 - 320 SC N Cast Aluminum 30 HSS 180 HSS Wrought Aluminum 30 HSS 180 HSS Aluminum Bronze 100 - 200 SC 200 - 250 SC Brass 100 HSS Copper 60 SC

SFM

TiN 170 155 140 150 140 130 120 140 130 120 110 130 120 110 105

TiAlN

TiCN

AM200®

250 230 210 220 210 195 185 210 195 185 175 185 175 155 145 135

230 205 185 195 185 175 155 185 175 155 150 175 155 145 135 125

290 265 245 255 245 225 215 245 225 215 205 215 205 180 170 155 110 195 170 140 110 90 75

95 70 50 45 85 70 50 25 20 35 26 65 50 65 50 65 50 65 50

95 75 65

85 70 60

120 105

170 145 120

155 135 110

95 80 35 30 45 40 90 80 90 80 90 80 90 80

90 75 30 25 40 35 85 70 85 70 85 70 85 70

95

40 35 50 45

110

90

110

90

110

90

110

90

- - -

- - -

- - -

- - -

45 25

65 40

60 35

80 45

150 130 110

220 195 175 150 120 750 400 750 400 190 150 220 150

195 175 150 125 105 650 350 650 350 175 125 190 130

255 225 205 175 140

95 80

520 260 520 260 130 150 115 95

- -

850 450 230 165 250 170

Contact our Application Engineering department for assistance when machining these materials

IMPORTANT: The speeds and feeds listed above are a general starting point for all applications. Refer to the Coolant Recommendation charts for coolant requirements to run at the recommended speeds and feeds. Factory technical assistance is available through our Application Engineering department. See adjustment examples on the following page.

44

www.alliedmachine.com | 1.330.343.4283

Made with FlippingBook Annual report