A55-4TX_US-EN

The 4TEX indexable carbide drill provides increased penetration rates on light duty machines due to the single effective design. With twisted coolant outlets and increased core strength, the design provides improved hole size and finish. The 4 sided 4TEX inserts are designed to use 2 sides in the center pocket and 2 sides in the periphery pocket for an improved cost-per-hole.

Boring

Reaming

Burnishing

Threading

4TEX ® Drill DRILLING Indexable Carbide Insert Drilling System

Specials

S E C T I O N A55 4TEX® Drill

4TEX® Drill Indexable Carbide Insert Drilling System

Diameter Range: 0.472" - 1.850" (12.00 mm - 47.00 mm)

Your safety and the safety of others is very important. This catalog contains important safety messages. Always read and follow all safety precautions. This triangle is a safety hazard symbol. It alerts you to potential safety hazards that can cause tool failure and serious injury. When you see this symbol in the catalog, look for a related safety message that may be near this triangle or referred to in the nearby text. There are safety signal words also used in the catalog. Safety messages follow these words. WARNING WARNING (shown above) means that failure to follow the precautions in this message could result in tool failure and serious injury. NOTICE means that failure to follow the precautions in this message could result in damage to the tool or machine but not result in personal injury. NOTE and IMPORTANT are also used. These are important that you read and follow but are not safety-related. Visit www.alliedmachine.com for the most up-to-date information and procedures.

Don’t Let Your Machine Slow You Down The 4TEX indexable carbide drill provides increased penetration rates on light duty machines due to the single effective design. With twisted coolant outlets and increased core strength, the design provides improved hole size and finish. The four sided 4TEX inserts are designed to use two sides in the center pocket and two sides in the periphery pocket for an improved cost per hole. With insert geometries available for all ISO material classes and a robust body design, the 4TEX is suited for your difficult applications.

Improved hole size and finish

Superior chip evacuation

Increased penetration rates

Applicable Industries

Aerospace Agriculture

Automotive

Firearms

General Machining

Oil & Gas

Renewable Energy

4TEX Drill Contents

Reference Icons The following icons will appear throughout the catalog to help you navigate between products.

Introduction Information

Safety Information . . . . . . . . . . . . . . . . . 2 Case Study . . . . . . . . . . . . . . . . . 3 Product Overview . . . . . . . . . . . . . . . . . 4 Insert Information . . . . . . . . . . . . . . . . 5 - 6 Product Nomenclature . . . . . . . . . . . . . . . . . 7

Setup / Assembly Information Detailed instructions and information regarding the corresponding part(s)

Recommended Cutting Data Speed and feed recommendations for optimum and safe drilling

Drill Series 03 Series . . . . . . . . . . . . . . . . 8 - 9 04 Series . . . . . . . . . . . . . . 10 - 11 05 Series . . . . . . . . . . . . . . 12 - 13 06 Series . . . . . . . . . . . . . . 14 - 15 07 Series . . . . . . . . . . . . . . 16 - 17 09 Series . . . . . . . . . . . . . . 18 - 21 11 Series . . . . . . . . . . . . . . 22 - 25 14 Series . . . . . . . . . . . . . . 26 - 29

Eccentric Sleeves Refers to the corresponding eccentric sleeve for the holder

Coolant-Through Option Indicates that the product is coolant through

Eccentric Sleeves . . . . . . . . . . . . . . . . . 30

Diameter Range

Series

Imperial (inch) 0.472 - 0.531 0.532 - 0.610 0.611 - 0.728 0.728 - 0.866 0.867 - 1.043 1.044 - 1.259 1.260 - 1.535 1.536 - 1.850

Metric (mm) 12.00 - 13.49 13.50 - 15.49 15.50 - 18.49 18.50 - 21.99 22.00 - 26.49 26.50 - 31.99 32.00 - 38.99 39.00 - 47.00

Technical Information Diameter Adjustment . . . . . . . . . . . . . . . . . 31 Center Height Alignment . . . . . . . . . . . . . . 32 - 33

03 04 05 06 07 09 11 14

Recommended Cutting Data

Imperial (inch) . . . . . . . . . . . . . . . . . 34 Metric (mm) . . . . . . . . . . . . . . . . . 35

Insert Geometry Recommendations . . . . . . . . . . . . . . . . . 36

Troubleshooting Guide . . . . . . . . . . . . . . . . . 37

A55: 1

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

Safety Information

A

DRILLING

Mechanical / Physical Hazards Operating cutting tools may present both mechanical and physical hazards. These hazards can result in serious injury to workers or those near machines and damage to machines and the cutting tools. Cutting tools and/or assemblies may break or come loose when in operation causing projectile metal fragments. Metal chips produced by cutting tools have sharp edges and may be very hot. To minimize the risk of mechanical or physical hazards: • Always secure all components of the cutting tool assembly before operating. • Wear cut-resistant gloves when handling cutting tool components and assemblies. • Do not touch metal chips produced by the cutting tools with your hands. • Always wear appropriate personal protective equipment including safety goggles or glasses with side shields. • Immediately discontinue use of damaged cutting tools. • To avoid machine tool damage, make sure the machine has adequate power and torque for the cutting tool when operating. See catalog for power and torque requirements. • Operating long cutting tools at high spindle speeds can result in a high risk of tool failure and serious injury. Grinding, welding, cutting or burning hard metals such as high-speed steel, cobalt or carbides produces hazardous dust and/or fumes. Continued long-term exposure to hazardous dust and fumes can cause serious health issues. To minimize the risk of dust and fume hazards: • Do not regrind or sharpen cutting tools without using adequate ventilation. • Use appropriate personal protective equipment such as approved respirator to avoid inhalation, swallowing, or skin contact with the hazardous dust and/or fumes. • Do not eat, drink, or smoke in the machine operation area. Always wash skin prior to eating, drinking, or smoking to avoid hazardous ingestion. Dust and Fume Hazards

B

BORING

C

REAMING

Sensitizing Hazards

Components of an assembled cutting tool are made from a variety of metal elements that may cause allergic skin reactions with prolonged skin contact. To minimize the risk of allergic skin reactions:

• Avoid skin contact with cutting tools. • Wear appropriate gloves and protective clothing. • Wash skin and launder clothing after handling cutting tools to reduce the risk of skin allergies.

D

Preventive Safety Measure Applicable to all Hazards

BURNISHING

• Prior to using cutting tools, always read Allied Machine’s Safety Data Sheets, product catalog, and product labels for additional warnings for the Allied Machine product being used. • For machining safety, only operate equipment when all necessary guards, interlocks and other safety devices are in place and functional. Use all appropriate safety guards or machine encapsulations to securely collect particles such as chips or cutting elements that may become projectiles.

Through Hole • With through holes, a sharp-edged disk is created as tool breakout occurs. Proper personal protective equipment must be used to prevent injury (e.g. wear cut-resistant gloves).

E

THREADING

X

SPECIALS

A55: 2

www.alliedmachine.com | 1.330.343.4283

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

Case Study

A

Do you need performance in extreme machining conditions? Tooling is only a sliver of the pie when it comes to productivity. It doesn’t matter what your tooling is capable of if your machine conditions restrict those capabilities. Our customer, who drills holes for machine gun bolt switches, utilizes a machine with oil coolant that creates more extreme drilling conditions than water-based coolant. Because oil coolant doesn’t dissipate heat fast enough, the customer’s tooling only lasted for 160 holes per insert, and the tool experienced sporadic failure. They also needed to run a peck cycle for chip control. The customer decided to test the 4TEX indexable carbide drill using the “P” geometry with AM480 coating designed specifically for wear-resistance in steel material applications. The 4TEX “P” geometry allowed for the speed and feed to be altered and accommodated the machine’s oil coolant. The 4TEX penetration rate was able to decrease cycle time and also double the tool life to 320 holes per insert. The 4TEX geometry also improved chip formation and eliminated the peck cycle. The 4TEX provided the stable and repeatable process the customer was looking for while increasing tool life by 100%. With all their objectives met, the customer was thrilled with the solution that optimized their machine’s limitations. Are you using the solution that best optimizes your machine’s limitations?

DRILLING

B

BORING

C

Product:

4TEX ® Drill

Measure

Competitor IC Drill

4TEX ® Drill

REAMING

Objectives:

(1) Exceed 160 holes per insert (2) Eliminate peck cycle (3) Provide stable/repeatable process

RPM

2075

1223

Speed Rate 509 SFM (155.1432 M/min) 300 SFM (91.44 M/min) Feed Rate 0.0015 IPR (0.0381 mm/rev) 0.003 IPR (0.0762 mm/rev) Penetration Rate 3.11 IPM (78.994 mm/min) 3.67 IPM (93.219 mm/min) Peck Cycle Yes No Cycle Time 16 sec 9 sec Tool Life 160 holes per insert 320 holes per insert

Industry:

Firearms

Part:

Machine gun bolt switch hole

Material: Hole Ø:

4340 steel

D

0.937" (23.7998 mm) Hole Depth: 0.590" (14.986 mm)

BURNISHING

4TEX Drill holder 2xD length Item No. D2070937I-100F

100% tool life increase

4TEX Drill inserts P geometry (steel) Item No. 4T-070305-P

E

THREADING

The 4-sided indexable inserts with wear resistant coating provided:

Increased tool life

X

Decreased cycle time

Worry-free machining

SPECIALS

© Allied Machine & Engineering CS2302

www.alliedmachine.com | 1.330.343.4283

A55: 3

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

Product Overview

A

4TEX Drill Advantages Superior chip evacuation provided by the two twisted coolant holes Improved hole size from the increased holder rigidity Longer tool life provided by the four-sided insert design Optimal chip formation

DRILLING

B

with ISO-specific insert geometry/coating combinations Competitive cycle times due to single effective cutting when using light duty machines

BORING

Double Coolant Hole

C

Center Insert Flute

Periphery Insert Flute

DESIGNED TO GIVE YOU IMPROVED HOLE SIZE AND STRAIGHTNESS

REAMING

• The two twisted coolant holes allow the core to remain intact, making the core thicker and stronger for improved hole straightness even in uneven surfaces. • The enlarged dual coolant outlets increase the coolant volume, which improved the chip evacuation resulting in improved hole size. • The flute space of the internal cutting edge side (where chips get stuck most often) is 1.6x larger than typical IC drills, helping to mitigate catastrophic failures and improve hole size.

D

BURNISHING

LONGER TOOL LIFE

AVAILABLE LENGTHS

2xD

E

THREADING

3xD

4xD

X

The 4 Edge Advantage When the cutting edge on the periphery insert wears down, it can be rotated and moved to the center insert position.

SPECIALS

A55: 4

www.alliedmachine.com | 1.330.343.4283

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

EDGES 4 Insert Information

A

CUTTING

DRILLING

Periphery Edge

Center Edge

Center Edge

• Each insert has two inner cutting edges and two outer cutting edges. • Economical solution that increases tool life because of the rotation ability of the inserts. • Available in ISO material-specific geometry/coating combinations.

B

Periphery Edge

BORING

Periphery Insert

Center Insert

180°

C

REAMING

Periphery edge chip formation:

Center edge chip formation:

D

BURNISHING

ISO Material

Geometry

Coating

Description

A general purpose geometry that provides excellent chip formation in most steels including free-machining, medium- and high-carbon steels. A P30 carbide substrate for improved toughness and AM480 coating, a proprietary wear resistant multilayer PVD coating to improve tool life. A higher rake geometry that provides excellent chip formation in both stainless steels and high-temperature alloys. A tough M25 carbide substrate coated with AM485, a high heat resistance proprietary multilayer PVD coating. A lower rake geometry to improve edge strength in both hardened tool steels and high strength alloys. With a P30 carbide substrate for improved toughness and coated with AM480, a proprietary multilayer PVD coating to improve resistance against tool wear. With a general purpose geometry, the K inserts can be used in grey cast irons as well as ductile irons. A high wear-resistant K10 carbide substrate to improve tool life and coated with AM480, a proprietary multilayer PVD coating to improve resistance against tool wear. A higher rake cutting geometry provides excellent chip formation in nonferrous materials. An M15/K15 carbide substrate paired with TiCN coating for improved lubricity to resist built-up material, increasing tool life and maintaining chip formation.

P

E

General Rake

AM480

THREADING

S M

High Rake

AM485

H

Low Rake

AM480

X

K

General Rake

AM480

SPECIALS

N

High Rake

TiCN

www.alliedmachine.com | 1.330.343.4283

A55: 5

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

Insert Information

A

Dimension (mm)

Angle

DRILLING

Series

Insert Prefix

Shape

L 1

L 2

T

D 1

R

A 1

A 2

4T-030203C-x

5.60

4.80

2.30

2.40

0.30

10°

B

Style 1

03

BORING

4T-030203P-x

6.38

4.77

2.30

2.40

0.30

10°

Style 2

4T-040203-x 4T-05T203-x 4T-06T204-x 4T-070305-x 4T-09T306-x 4T-11T306-x 4T-140408-x

04 05 06 07 09

6.21 7.26 8.59

5.06 5.48 6.44 8.02 9.55

2.60 2.76 2.89 3.24 4.03 4.06 4.88

2.45 2.55 2.79 3.00 3.64 4.62 5.76

0.30 0.30 0.40 0.50 0.60 0.60 0.80

13° 13° 13° 13° 13° 13° 13°

10°

7° 7° 7° 7° 7° 7°

C

10.21 12.18 14.50 17.99

REAMING 11

11.61 14.40

Style 3

14

Style 1

Style 2

Style 3

R

R

R

D

A 1

A 1

A 1

BURNISHING

D 1

D 1

D 1

L 1

L 1

L 1

T

L 2

L 2

T

L 2

T

E

A 2

A 2

A 2

THREADING

X

SPECIALS

A55: 6

www.alliedmachine.com | 1.330.343.4283

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

Product Nomenclature

A

4TEX Drill Holders

DRILLING

D4 03

1200

M - 075

F

1

2

3*

4

5

6

1. Length-to-Diameter-Ratio

2. Series

3. Diameter*

4. Diameter Style

D2 = 2xD D3 = 3xD D4 = 4xD

03 = 03 series 04 = 04 series 05 = 05 series 06 = 06 series

07 = 07 series 09 = 09 series 11 = 11 series 14 = 14 series

0750 = .075” 1200 = 12mm

I = Imperial M = Metric

B

BORING

*Ordering Nonstocked Diameters: Non-stocked diameters are available upon request. Please refer to price list for applicable process fees. Ordering example: Inch: 03 Series (Ø .480") = D2030480I-075F Metric: 03 Series (12.65 mm) = D2031265M-20FM

5. Shank Diameter

6. Shank Style

Imperial

Metric

F = Imperial flanged shank FM = Metric flanged shank

075 = 0.75" 100 = 1.000" 125 = 1.250" 150 = 1.500"

20 = 20 mm 25 = 25 mm 32 = 32 mm 40 = 40 mm

C

REAMING

Reference Key Symbol Attribute D 1

L 1

L 3

Drill diameter Shank diameter Flange diameter

L 2

D

D 2 D 3

D 1

D 2

D 3

BURNISHING

L 1 L 2 L 3

Assembled overall length

Drill depth

Reference length

E

THREADING

X

SPECIALS

www.alliedmachine.com | 1.330.343.4283

A55: 7

03

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

4TEX Drill Holders | Imperial Shank

A

03 Series | Diameter Range: 0.472" - 0.531" (12.00 mm - 13.49 mm)

L 1

DRILLING

L 3

L 2

D 1

D 2

D 3

B

Imperial Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2031200M-075F D2031250M-075F D2030500I-075F D2031300M-075F D3031200M-075F D3031250M-075F D3030500I-075F D3031300M-075F D4031200M-075F D4031250M-075F D4030500I-075F D4031300M-075F

0.472 0.492 0.500 0.512 0.472 0.492 0.500 0.512 0.472 0.492 0.500 0.512

12.00 12.50 12.70 13.00 12.00 12.50 12.70 13.00 12.00 12.50 12.70 13.00

0.945 0.984 1.000 1.024 1.417 1.476 1.500 1.535 1.890 1.969 2.000 2.047

1.787 1.827 1.827 1.866 2.260 2.319 2.319 2.378 2.732 2.811 2.811 2.890

3.480 3.520 3.520 3.559 3.953 4.012 4.012 4.071 4.425 4.504 4.504 4.583

0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750

1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063

0.020 0.016 0.014 0.012 0.020 0.016 0.014 0.012 0.020 0.016 0.014 0.012

2xD

C

3xD

REAMING

4xD

D

IC Inserts

Expected Hole Tolerances

Length

in

mm

Admissible Tightening Torque

BURNISHING

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Style

Part No.

Insert Screw

Torx® Driver

4T-030203C-P 4T-030203P-P 4T-030203C-M 4T-030203P-M 4T-030203C-H 4T-030203P-H 4T-030203C-K 4T-030203P-K 4T-030203C-N 4T-030203P-N

Center

P

Periphery

Center

S M

Periphery

Center

4.4 in-lbs (0.5 N-m)

H

7241-T6-1

8T-6

Periphery

Center

E

K

Periphery

Center

N

Periphery

THREADING

X

SPECIALS

A55: 34 - 35

A55: 31 - 33

A55: 30

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

A55: 8

www.alliedmachine.com | 1.330.343.4283

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

03

4TEX Drill Holders | Metric Shank 03 Series | Diameter Range: 0.472" - 0.531" (12.00 mm - 13.49 mm)

A

L 1

DRILLING

L 3

L 2

D 1

D 2

D 3

B

Metric Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2031200M-20FM D2031250M-20FM D2030500I-20FM D2031300M-20FM D3031200M-20FM D3031250M-20FM D3030500I-20FM D3031300M-20FM D4031200M-20FM D4031250M-20FM D4030500I-20FM D4031300M-20FM

0.472 0.492 0.500 0.512 0.472 0.492 0.500 0.512 0.472 0.492 0.500 0.512

12.00 12.50 12.70 13.00 12.00 12.50 12.70 13.00 12.00 12.50 12.70 13.00

24.00 25.00 25.40 26.00 36.00 37.50 38.10 39.00 48.00 50.00 50.80 52.00

45.40 46.40 46.40 47.40 57.40 58.90 58.90 60.40 69.40 71.40 71.40 73.40

88.40 89.40 89.40 90.40

20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00

27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00

0.50 0.40 0.35 0.30 0.50 0.40 0.35 0.30 0.50 0.40 0.35 0.30

2xD

100.40 101.90 101.90 103.40 112.40 114.40 114.40 116.40

C

3xD

REAMING

4xD

D

IC Inserts

Expected Hole Tolerances

Length

in

mm

Admissible Tightening Torque

BURNISHING

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Style

Part No.

Insert Screw

Torx® Driver

4T-030203C-P 4T-030203P-P 4T-030203C-M 4T-030203P-M 4T-030203C-H 4T-030203P-H 4T-030203C-K 4T-030203P-K 4T-030203C-N 4T-030203P-N

Center

P

Periphery

Center

S M

Periphery

Center

4.4 in-lbs (0.5 N-m)

H

7241-T6-1

8T-6

Periphery

Center

E

K

Periphery

Center

N

Periphery

THREADING

X

A55: 34 - 35

A55: 31 - 33

A55: 30

SPECIALS

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

www.alliedmachine.com | 1.330.343.4283

A55: 9

04

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

4TEX Drill Holders | Imperial Shank 04 Series | Diameter Range: 0.532" - 0.610" (13.50 mm - 15.49 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Imperial Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2041350M-075F D2041400M-075F D2040562I-075F D2041450M-075F D2041500M-075F D3041350M-075F D3041400M-075F D3040562I-075F D3041450M-075F D3041500M-075F D4041350M-075F D4041400M-075F D4040562I-075F D4041450M-075F D4041500M-075F

0.531 0.551 0.563 0.571 0.591 0.531 0.551 0.563 0.571 0.591 0.531 0.551 0.563 0.571 0.591

13.50 14.00 14.29 14.50 15.00 13.50 14.00 14.29 14.50 15.00 13.50 14.00 14.29 14.50 15.00

1.063 1.102 1.124 1.142 1.181 1.594 1.654 1.686 1.713 1.772 2.126 2.205 2.248 2.283 2.362

1.906 1.945 1.945 1.984 2.024 2.437 2.496 2.496 2.555 2.614 2.969 3.047 3.047 3.126 3.205

3.598 3.638 3.638 3.677 3.717 4.130 4.189 4.189 4.248 4.307 4.661 4.740 4.740 4.819 4.898

0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750

1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063

0.020 0.016 0.013 0.012 0.008 0.020 0.016 0.013 0.012 0.008 0.020 0.016 0.013 0.012 0.008

2xD

C

3xD

REAMING

4xD

D

BURNISHING IC Inserts

Expected Hole Tolerances

Length

in

mm

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-040203-P

S M 4T-040203-M H 4T-040203-H K 4T-040203-K N 4T-040203-N

4.4 in-lbs (0.5 N-m)

7241-T6-1

8T-6

E

THREADING

X

SPECIALS

A55: 34 - 35

A55: 31 - 33

A55: 30

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

A55: 10

www.alliedmachine.com | 1.330.343.4283

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

04

4TEX Drill Holders | Metric Shank 04 Series | Diameter Range: 0.532" - 0.610" (13.50 mm - 15.49 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Metric Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2041350M-20FM D2041400M-20FM D2040562I-20FM D2041450M-20FM D2041500M-20FM D3041350M-20FM D3041400M-20FM D3040562I-20FM D3041450M-20FM D3041500M-20FM D4041350M-20FM D4041400M-20FM D4040562I-20FM D4041450M-20FM D4041500M-20FM

0.531 0.551 0.563 0.571 0.591 0.531 0.551 0.563 0.571 0.591 0.531 0.551 0.563 0.571 0.591

13.50 14.00 14.29 14.50 15.00 13.50 14.00 14.29 14.50 15.00 13.50 14.00 14.29 14.50 15.00

27.00 28.00 28.55 29.00 30.00 40.50 42.00 42.82 43.50 45.00 54.00 56.00 57.10 58.00 60.00

48.40 49.40 49.40 50.40 51.40 61.90 63.40 63.40 64.90 66.40 75.40 77.40 77.40 79.40 81.40

91.40 92.40 92.40 93.40 94.40

20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00

27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00

0.50 0.40 0.30 0.30 0.20 0.50 0.40 0.30 0.30 0.20 0.50 0.40 0.30 0.30 0.20

2xD

104.90 106.40 106.40 107.90 109.40 118.40 120.40 120.40 122.40 124.40

C

3xD

REAMING

4xD

D

BURNISHING

IC Inserts

Expected Hole Tolerances

Length

in

mm

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-040203-P

S M 4T-040203-M H 4T-040203-H K 4T-040203-K N 4T-040203-N

4.4 in-lbs (0.5 N-m)

7241-T6-1

8T-6

E

THREADING

X

A55: 34 - 35

A55: 31 - 33

A55: 30

SPECIALS

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

www.alliedmachine.com | 1.330.343.4283

A55: 11

05

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

4TEX Drill Holders | Imperial Shank 05 Series | Diameter Range: 0.611" - 0.728" (15.50 mm - 18.49 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Imperial Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2051550M-100F D2050625I-100F D2051600M-100F D2051650M-100F D2050656I-100F D2051700M-100F D2050687I-100F D2051750M-100F D2051800M-100F D2050718I-100F D3051550M-100F D3050625I-100F D3051600M-100F D3051650M-100F D3050656I-100F D3051700M-100F D3050687I-100F D3051750M-100F D3051800M-100F D3050718I-100F D4051550M-100F D4050625I-100F D4051600M-100F D4051650M-100F D4050656I-100F D4051700M-100F D4050687I-100F D4051750M-100F D4051800M-100F D4050718I-100F

0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718 0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718 0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718

15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24 15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24 15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24

1.220 1.250 1.260 1.299 1.312 1.339 1.374 1.378 1.417 1.436 1.831 1.875 1.890 1.949 1.968 2.008 2.061 2.067 2.126 2.154 2.441 2.500 2.520 2.598 2.624 2.677 2.748 2.756 2.835 2.872

2.146 2.146 2.185 2.224 2.224 2.264 2.264 2.303 2.343 2.343 2.756 2.756 2.815 2.874 2.784 2.933 2.933 2.992 3.051 3.051 3.366 3.366 3.445 3.524 3.524 3.602 3.602 3.681 3.760 3.760

4.272 4.272 4.311 4.350 4.350 4.390 4.390 4.429 4.469 4.469 4.882 4.882 4.941 5.000 5.000 5.059 5.059 5.118 5.177 5.177 5.492 5.492 5.571 5.650 5.650 5.728 5.728 5.807 5.886 5.886

1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000

1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260

0.031 0.029 0.028 0.020 0.016 0.016 0.012 0.012 0.008 0.006 0.031 0.029 0.028 0.020 0.016 0.016 0.012 0.012 0.008 0.006 0.031 0.029 0.028 0.020 0.016 0.016 0.012 0.012 0.008 0.006

2xD

C

REAMING

3xD

D

BURNISHING

4xD

E

THREADING IC Inserts

Expected Hole Tolerances

Length

in

mm

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-05T203-P

S M 4T-05T203-M H 4T-05T203-H K 4T-05T203-K N 4T-05T203-N

4.4 in-lbs (0.5 N-m)

7243-T6-1

8T-6

X

SPECIALS

A55: 34 - 35

A55: 31 - 33

A55: 30

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

A55: 12

www.alliedmachine.com | 1.330.343.4283

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

05

4TEX Drill Holders | Metric Shank 05 Series | Diameter Range: 0.611" - 0.728" (15.50 mm - 18.49 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Metric Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2051550M-25FM D2050625I-25FM D2051600M-25FM D2051650M-25FM D2050656I-25FM D2051700M-25FM D2050687I-25FM D2051750M-25FM D2051800M-25FM D2050718I-25FM D3051550M-25FM D3050625I-25FM D3051600M-25FM D3051650M-25FM D3050656I-25FM D3051700M-25FM D3050687I-25FM D3051750M-25FM D3051800M-25FM D3050718I-25FM D4051550M-25FM D4050625I-25FM D4051600M-25FM D4051650M-25FM D4050656I-25FM D4051700M-25FM D4050687I-25FM D4051750M-25FM D4051800M-25FM D4050718I-25FM

0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718 0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718 0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718

15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24 15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24 15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24

31.00 31.75 32.00 33.00 33.32 34.00 34.90 35.00 36.00 36.47 46.50 47.63 48.00 49.50 49.98 51.00 52.35 52.50 54.00 54.71 62.00 63.50 64.00 66.00 66.64 68.00 69.80 70.00 72.00 72.95

54.50 54.50 55.50 56.50 56.49 57.50 57.50 58.50 59.50 59.51 70.00 70.00 71.50 73.00 73.00 74.50 74.50 76.00 77.50 77.50 85.50 85.50 87.50 89.50 89.51 91.50 91.50 93.50 95.50 95.50

108.50 108.50 109.50 110.50 110.50 111.50 111.50 112.50 113.50 113.51 124.00 124.00 125.50 127.00 127.00 128.50 128.50 130.00 131.50 131.50 139.50 139.50 141.50 143.50 143.51 145.50 145.50 147.50 149.50 149.50

25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 58.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00

32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00

0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.30 0.20 0.15 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.30 0.20 0.15 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.30 0.20 0.15

2xD

C

REAMING

3xD

D

BURNISHING

4xD

E

THREADING

IC Inserts

Expected Hole Tolerances

Length

in

mm

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-05T203-P

S M 4T-05T203-M H 4T-05T203-H K 4T-05T203-K N 4T-05T203-N

4.4 in-lbs (0.5 N-m)

7243-T6-1

8T-6

X

A55: 34 - 35

A55: 31 - 33

A55: 30

SPECIALS

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

www.alliedmachine.com | 1.330.343.4283

A55: 13

06

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

4TEX Drill Holders | Imperial Shank 06 Series | Diameter Range: 0.728" - 0.866" (18.50 mm - 21.99 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Imperial Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2061850M-100F D2061900M-100F D2060750I-100F D2060765I-100F D2061950M-100F D2062000M-100F D2062050M-100F D2060812I-100F D2062100M-100F D2062150M-100F D3061850M-100F D3061900M-100F D3060750I-100F D3060765I-100F D3061950M-100F D3062000M-100F D3062050M-100F D3060812I-100F D3062100M-100F D3062150M-100F D4061850M-100F D4061900M-100F D4060750I-100F D4060765I-100F D4061950M-100F D4062000M-100F D4062050M-100F D4060812I-100F D4062100M-100F D4062150M-100F

0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846 0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846 0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846

18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50 18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50 18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50

1.457 1.496 1.500 1.530 1.535 1.575 1.614 1.624 1.654 1.693 2.165 2.244 2.250 2.295 2.303 2.362 2.421 2.436 2.480 2.539 2.913 2.992 3.000 3.060 3.071 3.150 3.228 3.248 3.307 3.386

2.299 2.339 2.339 2.339 2.378 2.417 2.457 2.457 2.496 2.535 3.028 3.087 3.087 3.087 3.146 3.205 3.264 3.264 3.323 3.382 3.756 3.835 3.835 3.835 3.913 3.992 4.071 4.071 4.150 4.228

4.425 4.465 4.465 4.465 4.504 4.543 4.583 4.583 4.622 4.661 5.154 5.213 5.213 5.213 5.272 5.331 5.390 5.390 5.449 5.508 5.882 5.961 5.961 5.961 6.039 6.118 6.197 6.197 6.276 6.354

1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000

1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260

0.035 0.031 0.031 0.028 0.028 0.020 0.016 0.015 0.012 0.008 0.035 0.031 0.031 0.028 0.028 0.020 0.016 0.015 0.012 0.008 0.035 0.031 0.031 0.028 0.028 0.020 0.016 0.015 0.012 0.008

2xD

C

REAMING

3xD

D

BURNISHING

4xD

E

THREADING IC Inserts

Expected Hole Tolerances

Length

in

mm

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-06T204-P

S M 4T-06T204-M H 4T-06T204-H K 4T-06T204-K N 4T-06T204-N

7.1 in-lbs (0.8 N-m)

72251-T7-1

8T-7

X

SPECIALS

A55: 34 - 35

A55: 31 - 33

A55: 30

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

A55: 14

www.alliedmachine.com | 1.330.343.4283

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

06

4TEX Drill Holders | Metric Shank 06 Series | Diameter Range: 0.728" - 0.866" (18.50 mm - 21.99 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Metric Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2061850M-25FM D2061900M-25FM D2060750I-25FM D2060765I-25FM D2061950M-25FM D2062000M-25FM D2062050M-25FM D2060812I-25FM D2062100M-25FM D2062150M-25FM D3061850M-25FM D3061900M-25FM D3060750I-25FM D3060765I-25FM D3061950M-25FM D3062000M-25FM D3062050M-25FM D3060812I-25FM D3062100M-25FM D3062150M-25FM D4061850M-25FM D4061900M-25FM D4060750I-25FM D4060765I-25FM D4061950M-25FM D4062000M-25FM D4062050M-25FM D4060812I-25FM D4062100M-25FM D4062150M-25FM

0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846 0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846 0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846

18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50 18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50 18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50

37.00 38.00 38.10 38.86 39.00 40.00 41.00 41.25 42.00 43.00 55.00 57.00 57.15 58.29 58.50 60.00 61.50 61.87 63.00 64.50 74.00 76.00 76.20 77.72 78.00 80.00 82.00 82.49 84.00 86.00

58.40 59.40 59.40 59.41 60.40 61.40 62.40 62.40 63.40 64.40 76.90 78.40 78.40 78.41 79.90 81.40 82.90 82.90 84.40 85.90 95.40 97.40 97.40 97.41 99.40

112.40 113.40 113.40 113.41 114.40 115.40 116.40 116.40 117.40 118.40 130.90 132.40 132.40 132.41 133.90 135.40 136.90 136.90 138.40 139.90 149.40 151.40 151.40 151.41 153.40 155.40 157.40 157.40 159.40 161.40

25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00

32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00

0.90 0.80 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.20 0.90 0.80 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.20 0.90 0.80 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.20

2xD

C

REAMING

3xD

D

BURNISHING

4xD

101.40 103.40 103.40 105.40 107.40

E

THREADING

IC Inserts

Expected Hole Tolerances

Length

in

mm

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-06T204-P

S M 4T-06T204-M H 4T-06T204-H K 4T-06T204-K N 4T-06T204-N

7.1 in-lbs (0.8 N-m)

72251-T7-1

8T-7

X

A55: 34 - 35

A55: 31 - 33

A55: 30

SPECIALS

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

www.alliedmachine.com | 1.330.343.4283

A55: 15

07

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

4TEX Drill Holders | Imperial Shank 07 Series | Diameter Range: 0.867" - 1.043" (22.00 mm - 26.49 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Imperial Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2072200M-100F D2070875I-100F D2072250M-100F D2072300M-100F D2072350M-100F D2070937I-100F D2072400M-100F D2072450M-100F D2072500M-100F D2071000I-100F D2072550M-100F D2072600M-100F D3072200M-100F D3070875I-100F D3072250M-100F D3072300M-100F D3072350M-100F D3070937I-100F D3072400M-100F D3072450M-100F D3072500M-100F D3071000I-100F D3072550M-100F D3072600M-100F D4072200M-100F D4070875I-100F D4072250M-100F D4072300M-100F D4072350M-100F D4070937I-100F D4072400M-100F D4072450M-100F D4072500M-100F D4071000I-100F D4072550M-100F D4072600M-100F

0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024 0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024 0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024

22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00 22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00 22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00

1.732 1.750 1.772 1.811 1.850 1.874 1.890 1.929 1.969 2.000 2.008 2.047 2.598 2.625 2.657 2.717 2.776 2.811 2.835 2.894 2.953 3.000 3.012 3.071 3.465 3.500 3.543 3.622 3.701 3.748 3.780 3.858 3.937 4.000 4.016 4.094

2.555 2.555 2.594 2.634 2.673 2.673 2.713 2.752 2.791 2.791 2.831 2.870 3.421 3.421 3.480 3.539 3.598 3.598 3.657 3.717 3.776 3.776 3.835 3.894 4.287 4.287 4.366 4.445 4.524 4.524 4.602 4.681 4.760 4.760 4.839 4.917

4.681 4.681 4.720 4.760 4.799 4.799 4.839 4.878 4.917 4.917 4.957 4.996 5.547 5.547 5.606 5.665 5.724 5.724 5.783 5.843 5.902 5.902 5.961 6.020 6.413 6.413 6.492 6.571 6.650 6.650 6.728 6.807 6.886 6.886 6.965 7.043

1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000

1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299

0.047 0.043 0.039 0.035 0.031 0.292 0.028 0.020 0.016 0.013 0.012 0.008 0.047 0.043 0.039 0.035 0.031 0.292 0.028 0.020 0.016 0.013 0.012 0.008 0.047 0.043 0.039 0.035 0.031 0.292 0.028 0.020 0.016 0.013 0.012 0.008

2xD

C

REAMING

3xD

D

BURNISHING

4xD

E

THREADING

IC Inserts

Expected Hole Tolerances

Length

in

mm

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-070305-P

S M 4T-070305-M H 4T-070305-H K 4T-070305-K N 4T-070305-N

10.6 in-lbs (1.2 N-m)

72568-T8-1

8T-8

X

SPECIALS

A55: 34 - 35

A55: 31 - 33

A55: 30

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

A55: 16

www.alliedmachine.com | 1.330.343.4283

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

07

4TEX Drill Holders | Metric Shank 07 Series | Diameter Range: 0.867" - 1.043" (22.00 mm - 26.49 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Metric Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2072200M-25FM D2070875I-25FM D2072250M-25FM D2072300M-25FM D2072350M-25FM D2070937I-25FM D2072400M-25FM D2072450M-25FM D2072500M-25FM D2071000I-25FM D2072550M-25FM D2072600M-25FM D3072200M-25FM D3070875I-25FM D3072250M-25FM D3072300M-25FM D3072350M-25FM D3070937I-25FM D3072400M-25FM D3072450M-25FM D3072500M-25FM D3071000I-25FM D3072550M-25FM D3072600M-25FM D4072200M-25FM D4070875I-25FM D4072250M-25FM D4072300M-25FM D4072350M-25FM D4070937I-25FM D4072400M-25FM D4072450M-25FM D4072500M-25FM D4071000I-25FM D4072550M-25FM D4072600M-25FM

0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024 0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024 0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024

22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00 22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00 22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00

44.00 44.45 45.00 46.00 47.00 47.60 48.00 49.00 50.00 50.80 51.00 52.00 66.00 66.68 67.50 69.00 70.50 71.40 72.00 73.50 75.00 76.20 76.50 78.00 88.00 88.90 90.00 92.00 94.00 95.20 96.00 98.00

64.90 64.90 65.90 66.90 67.90 67.90 68.90 69.90 70.90 70.90 71.90 72.90 86.90 86.90 88.40 89.90 91.40 91.40 92.90 94.40 95.90 95.90 97.00 99.00

118.90 118.90 119.90 120.90 121.90 121.90 122.90 123.90 124.90 124.90 125.90 126.90 140.90 140.90 142.40 143.90 145.40 145.40 146.90 148.40 149.90 149.90 151.00 153.00 163.00 162.90 165.00 167.00 169.00 168.90 171.00 173.00 175.00 174.90 177.00 179.00

25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00

33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00

1.20 1.10 1.00 0.90 0.80 7.40 0.70 0.50 0.40 0.30 0.30 0.20 1.20 1.10 1.00 0.90 0.80 7.40 0.70 0.50 0.40 0.30 0.30 0.20 1.20 1.10 1.00 0.90 0.80 7.40 0.70 0.50 0.40 0.30 0.30 0.20

2xD

C

REAMING

3xD

D

BURNISHING

109.00 108.90 111.00 113.00 115.00 114.90 117.00 119.00 121.00 120.90 123.00 125.00

4xD

100.00 101.60 102.00 104.00

E

THREADING

IC Inserts

Expected Hole Tolerances

Length

in

mm

2xD 3xD 4xD

-.004 / +.008 -.004 / +.008 -.004 / +.010

-.10 / +.20 -.10 / +.20 -.10 / +.25

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-070305-P

S M 4T-070305-M H 4T-070305-H K 4T-070305-K N 4T-070305-N

10.6 in-lbs (1.2 N-m)

72568-T8-1

8T-8

X

A55: 34 - 35

A55: 31 - 33

A55: 30

SPECIALS

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

www.alliedmachine.com | 1.330.343.4283

A55: 17

09

DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System

4TEX Drill Holders | Imperial Shank 09 Series | Diameter Range: 1.044" - 1.259" (26.50 mm - 31.99 mm)

A

DRILLING

L 1

L 3

L 2

D 1

D 2

D 3

B

Imperial Shank

Body

Shank

D 1

BORING

Length

in

mm

Max Offset

Part No.

L 2

L 3

L 1

D 2

D 3

D2092650M-125F D2092700M-125F D2092750M-125F D2092800M-125F D2092850M-125F D2091125I-125F D2092900M-125F D2092950M-125F D2093000M-125F D2091187I-125F D2093050M-125F D2093100M-125F D2093150M-125F D2091250I-125F D3092650M-125F D3092700M-125F D3092750M-125F D3092800M-125F D3092850M-125F D3091125I-125F D3092900M-125F D3092950M-125F D3093000M-125F D3091187I-125F D3093050M-125F D3093100M-125F D3093150M-125F D3091250I-125F

1.043 1.063 1.083 1.102 1.122 1.125 1.142 1.161 1.181 1.187 1.201 1.220 1.240 1.250 1.043 1.063 1.083 1.102 1.122 1.125 1.142 1.161 1.181 1.187 1.201 1.220 1.240 1.250

26.50 27.00 27.50 28.00 28.50 28.58 29.00 29.50 30.00 30.15 30.50 31.00 31.50 31.75 26.50 27.00 27.50 28.00 28.50 28.58 29.00 29.50 30.00 30.15 30.50 31.00 31.50 31.75

2.087 2.126 2.165 2.205 2.244 2.250 2.283 2.323 2.362 2.374 2.402 2.441 2.480 2.500 3.130 3.189 3.248 3.307 3.366 3.375 3.425 3.484 3.543 3.561 3.602 3.661 3.720 3.750

2.980 3.020 3.059 3.098 3.138 3.138 3.177 3.217 3.256 3.256 3.295 3.335 3.374 3.374 4.024 4.083 4.142 4.201 4.260 4.260 4.319 4.378 4.437 4.437 4.496 4.555 4.614 4.614

5.303 5.343 5.382 5.421 5.461 5.461 5.500 5.539 5.579 5.579 5.618 5.657 5.697 5.697 6.346 6.406 6.465 6.524 6.583 6.583 6.642 6.701 6.760 6.760 6.819 6.878 6.937 6.937

1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250

1.614 1.614 1.614 1.614 1.614 1.614 1.614 1.693 1.693 1.693 1.693 1.693 1.693 1.693 1.614 1.614 1.614 1.614 1.614 1.614 1.614 1.693 1.693 1.693 1.693 1.693 1.693 1.693

0.066 0.063 0.057 0.051 0.048 0.046 0.043 0.038 0.031 0.032 0.029 0.024 0.020 0.019 0.066 0.063 0.057 0.051 0.048 0.046 0.043 0.038 0.031 0.032 0.029 0.024 0.020 0.019

C

2xD

REAMING

D

BURNISHING

3xD

E

IC Inserts

Expected Hole Tolerances

THREADING

Length

in

mm

2xD 3xD 4xD

-.006 / +.010 -.006 / +.010 -.006 / +.012

-.15 / +.25 -.15 / +.25 -.15 / +.30

ISO Material

Admissible Tightening Torque

Part No.

Insert Screw

Torx® Driver

P

4T-09T306-P

S M 4T-09T306-M H 4T-09T306-H K 4T-09T306-K N 4T-09T306-N

17.7 in-lbs (2.0 N-m)

738-T10-1

8T-10

X

SPECIALS

A55: 34 - 35

A55: 31 - 33

A55: 30

= Imperial (in) = Metric (mm)

Key on A55: 1

IC inserts sold in quantities of 10 Insert screws sold in quantities of 10

A55: 18

www.alliedmachine.com | 1.330.343.4283

Made with FlippingBook Online newsletter