A55-4TX_EU-EN
Indexable insert drilling system
Boring
Reaming
Burnishing
Threading
4TEX ® Drill DRILLING Indexable Insert Drilling System
Specials
S E C T I O N A55 4TEX® Drill
4TEX® Drill Indexable Carbide Insert Drilling System
Diameter Range: 12.00 mm - 47.00 mm (0.472" - 1.850")
Your safety and the safety of others is very important. This catalogue contains important safety messages. Always read and follow all safety precautions. This triangle is a safety hazard symbol. It alerts you to potential safety hazards that can cause tool failure and serious injury. When you see this symbol in the catalogue, look for a related safety message that may be near this triangle or referred to in the nearby text. There are safety signal words also used in the catalogue. Safety messages follow these words. WARNING WARNING (shown above) means that failure to follow the precautions in this message could result in tool failure and serious injury. NOTICE means that failure to follow the precautions in this message could result in damage to the tool or machine but not result in personal injury. NOTE and IMPORTANT are also used. These are important that you read and follow but are not safety-related. Visit www.alliedmachine.com for the most up-to-date information and procedures.
Don’t Let Your Machine Slow You Down The 4TEX indexable carbide drill provides increased penetration rates on light duty machines due to the single effective design. With twisted coolant outlets and increased core strength, the design provides improved hole size and finish. The four-sided 4TEX inserts are designed to use two sides in the center pocket and two sides in the periphery pocket for an improved cost per hole. With insert geometries available for all ISO material classes and a robust body design, the 4TEX is suited for your difficult applications.
Improved hole size and finish
Superior chip evacuation
Increased penetration rates
Applicable Industries
Aerospace Agriculture
Automotive
Firearms
General Machining
Oil & Gas
Renewable Energy
4TEX Drill Contents
Reference Icons The following icons will appear throughout the catalogue to help you navigate between products.
Introduction Information
Product Overview . . . . . . . . . . . . . . . . . 2 Insert Information . . . . . . . . . . . . . . . . 3 - 4 Product Nomenclature . . . . . . . . . . . . . . . . . 5
Setup / Assembly Information Detailed instructions and information regarding the corresponding part(s)
Recommended Cutting Data Speed and feed recommendations for optimum and safe drilling
Drill Series 03 Series . . . . . . . . . . . . . . . . 6 - 7 04 Series . . . . . . . . . . . . . . . 8 - 9 05 Series . . . . . . . . . . . . . . 10 - 11 06 Series . . . . . . . . . . . . . . 12 - 13 07 Series . . . . . . . . . . . . . . 14 - 15 09 Series . . . . . . . . . . . . . . 16 - 19 11 Series . . . . . . . . . . . . . . 20 - 23 14 Series . . . . . . . . . . . . . . 24 - 27
Eccentric Sleeves Refers to the corresponding eccentric sleeve for the holder
Through Coolant Option Indicates that the product is through coolant
Eccentric Sleeves . . . . . . . . . . . . . . . . . 28
Technical Information Diameter Adjustment . . . . . . . . . . . . . . . . . 29 Center Height Alignment . . . . . . . . . . . . . . 30 - 31
Diameter Range
Series
Metric (mm) 12.00 - 13.49 13.50 - 15.49 15.50 - 18.49 18.50 - 21.99 22.00 - 26.49 26.50 - 31.99 32.00 - 38.99 39.00 - 47.00
Imperial (inch) 0.472 - 0.531 0.532 - 0.610 0.611 - 0.728 0.728 - 0.866 0.867 - 1.043 1.044 - 1.259 1.260 - 1.535 1.536 - 1.850
03 04 05 06 07 09 11 14
Recommended Cutting Data
Metric (mm) . . . . . . . . . . . . . . . . . 32 Imperial (inch) . . . . . . . . . . . . . . . . . 33
Insert Geometry Recommendations . . . . . . . . . . . . . . . . . 34
Troubleshooting Guide . . . . . . . . . . . . . . . . . 35
Safety Information . . . . . . . . . . . . . . . . . 36
A55: 1
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
Product Overview
A
4TEX Drill Advantages Superior chip evacuation provided by the two twisted coolant holes Improved hole size from the increased holder rigidity Longer tool life provided by the four-sided insert design Optimal chip formation
DRILLING
B
with ISO-specific insert geometry/coating combinations Competitive cycle times due to single effective cutting when using light duty machines
BORING
Double Coolant Hole
Center Insert Flute
C
Periphery Insert Flute
DESIGNED TO GIVE YOU IMPROVED HOLE SIZE AND STRAIGHTNESS
REAMING
• The two twisted coolant holes allow the core to remain intact, making the core thicker and stronger for improved hole straightness even in uneven surfaces. • The enlarged dual coolant outlets increase the coolant volume, which improved the chip evacuation resulting in improved hole size. • The flute space of the internal cutting edge side (where chips get stuck most often) is 1.6x larger than typical IC drills, helping to mitigate catastrophic failures and improve hole size.
D
BURNISHING
LONGER TOOL LIFE
AVAILABLE LENGTHS
2xD
E
THREADING
3xD
4xD
X
The 4 Edge Advantage When the cutting edge on the periphery insert wears down, it can be rotated and moved to the center insert position.
SPECIALS
A55: 2
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
EDGES 4 Insert Information
A
CUTTING
Periphery Edge
DRILLING
Center Edge
Center Edge
• Each insert has two inner cutting edges and two outer cutting edges. • Economical solution that increases tool life because of the rotation ability of the inserts. • Available in ISO material-specific geometry/coating combinations.
Periphery Edge
B
BORING
Periphery Insert
Center Insert
180°
C
REAMING
Periphery edge chip formation:
Center edge chip formation:
D
BURNISHING
ISO Material
Geometry
Coating
Description
A general purpose geometry that provides excellent chip formation in most steels including free-machining, medium- and high-carbon steels. A P30 carbide substrate for improved toughness and AM480 coating, a proprietary wear resistant multilayer PVD coating to improve tool life. A higher rake geometry that provides excellent chip formation in both stainless steels and high-temperature alloys. A tough M25 carbide substrate coated with AM485, a high heat resistance proprietary multilayer PVD coating. A lower rake geometry to improve edge strength in both hardened tool steels and high strength alloys. With a P30 carbide substrate for improved toughness and coated with AM480, a proprietary multilayer PVD coating to improve resistance against tool wear. With a general purpose geometry, the K inserts can be used in grey cast irons as well as ductile irons. A high wear-resistant K10 carbide substrate to improve tool life and coated with AM480, a proprietary multilayer PVD coating to improve resistance against tool wear. A higher rake cutting geometry provides excellent chip formation in nonferrous materials. An M15/K15 carbide substrate paired with TiCN coating for improved lubricity to resist built-up material, increasing tool life and maintaining chip formation.
P
General Rake
AM480
S M
High Rake
AM485
E
THREADING
H
Low Rake
AM480
K
General Rake
AM480
N
High Rake
TiCN
X
SPECIALS
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A55: 3
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
Insert Information
A
Dimension (mm)
Angle
Series
Insert Prefix
Shape
L 1
L 2
T
D 1
R
A 1
A 2
DRILLING
4T-030203C-x
5.60
4.80
2.30
2.40
0.30
7°
10°
Style 1
03
B
4T-030203P-x
6.38
4.77
2.30
2.40
0.30
7°
10°
BORING
Style 2
4T-040203-x 4T-05T203-x 4T-06T204-x 4T-070305-x 4T-09T306-x 4T-11T306-x 4T-140408-x
04 05 06 07 09 11 14
6.21 7.26 8.59
5.06 5.48 6.44 8.02 9.55
2.60 2.76 2.89 3.24 4.03 4.06 4.88
2.45 2.55 2.79 3.00 3.64 4.62 5.76
0.30 0.30 0.40 0.50 0.60 0.60 0.80
13° 13° 13° 13° 13° 13° 13°
10°
7° 7° 7° 7° 7° 7°
10.21 12.18 14.50 17.99
C
11.61 14.40
Style 3
REAMING
Style 1
Style 2
Style 3
R
R
R
A 1
A 1
A 1
D 1
D 1
D 1
L 1
L 1
L 1
D
BURNISHING
T
L 2
L 2
T
L 2
T
A 2
A 2
A 2
E
THREADING
X
SPECIALS
A55: 4
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
Product Nomenclature
4TEX Drill Holders
A
D4 03
1200
M - 20 FM
DRILLING
1
2
3*
4
5
6
1. Length to Diameter Ratio
2. Series
3. Diameter*
4. Diameter Style
D2 = 2xD D3 = 3xD D4 = 4xD
03 = 03 series 04 = 04 series 05 = 05 series 06 = 06 series
07 = 07 series 09 = 09 series 11 = 11 series 14 = 14 series
1200 = 12 mm 0750 = 0.075"
M = Metric I = Imperial
B
BORING
*Ordering Non-Stocked Diameters: Non-stocked diameters are available upon request. Please refer to price list for applicable process fees. Ordering example: Metric: 03 Series (12.65 mm) = D2031265M-20FM Inch: 03 Series (Ø 0.480") = D2030480I-075F
5. Shank Diameter
6. Shank Style
Metric
Imperial
FM = Metric flanged shank F = Imperial flanged shank
20 = 20 mm 25 = 25 mm 32 = 32 mm 40 = 40 mm
075 = 0.75" 100 = 1.000" 125 = 1.250" 150 = 1.500"
C
REAMING
Reference Key Symbol Attribute D 1
L 1
L 3
Drill diameter Shank diameter Flange diameter
L 2
D 2 D 3
D 1
D 2
D 3
L 1 L 2 L 3
Assembled overall length
D
Drill depth
Reference length
BURNISHING
E
THREADING
X
SPECIALS
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A55: 5
03
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Metric Shank 03 Series | Diameter Range: 12.00 mm - 13.49 mm (0.472" - 0.531")
A
L 1
L 3
DRILLING
L 2
D 1
D 2
D 3
Metric Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2031200M-20FM D2031250M-20FM D2030500I-20FM D2031300M-20FM D3031200M-20FM D3031250M-20FM D3030500I-20FM D3031300M-20FM D4031200M-20FM D4031250M-20FM D4030500I-20FM D4031300M-20FM
12.00 12.50 12.70 13.00 12.00 12.50 12.70 13.00 12.00 12.50 12.70 13.00
0.472 0.492 0.500 0.512 0.472 0.492 0.500 0.512 0.472 0.492 0.500 0.512
24.00 25.00 25.40 26.00 36.00 37.50 38.10 39.00 48.00 50.00 50.80 52.00
45.40 46.40 46.40 47.40 57.40 58.90 58.90 60.40 69.40 71.40 71.40 73.40
88.40 89.40 89.40 90.40
20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00
27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00
0.50 0.40 0.35 0.30 0.50 0.40 0.35 0.30 0.50 0.40 0.35 0.30
2xD
100.40 101.90 101.90 103.40 112.40 114.40 114.40 116.40
3xD
C
4xD
REAMING
IC Inserts
Expected Hole Tolerances
Length
mm
in
Admissible Tightening Torque
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
ISO Material
D
Style
Part No.
Insert Screw
Torx® Driver
4T-030203C-P 4T-030203P-P 4T-030203C-M 4T-030203P-M 4T-030203C-H 4T-030203P-H 4T-030203C-K 4T-030203P-K 4T-030203C-N 4T-030203P-N
Center
BURNISHING P
Periphery
Center
S M
Periphery
Center
0.5 N-m (4.4 in-lbs)
H
7241-T6-1
8T-6
Periphery
Center
K
Periphery
Center
N
Periphery
E
THREADING
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
A55: 6
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
03
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Imperial Shank
03 Series | Diameter Range: 12.00 mm - 13.49 mm (0.472" - 0.531")
A
L 1
L 3
DRILLING
L 2
D 1
D 2
D 3
Imperial Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2031200M-075F D2031250M-075F D2030500I-075F D2031300M-075F D3031200M-075F D3031250M-075F D3030500I-075F D3031300M-075F D4031200M-075F D4031250M-075F D4030500I-075F D4031300M-075F
12.00 12.50 12.70 13.00 12.00 12.50 12.70 13.00 12.00 12.50 12.70 13.00
0.472 0.492 0.500 0.512 0.472 0.492 0.500 0.512 0.472 0.492 0.500 0.512
0.945 0.984 1.000 1.024 1.417 1.476 1.500 1.535 1.890 1.969 2.000 2.047
1.787 1.827 1.827 1.866 2.260 2.319 2.319 2.378 2.732 2.811 2.811 2.890
3.480 3.520 3.520 3.559 3.953 4.012 4.012 4.071 4.425 4.504 4.504 4.583
0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750
1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063
0.020 0.016 0.014 0.012 0.020 0.016 0.014 0.012 0.020 0.016 0.014 0.012
2xD
3xD
C
4xD
REAMING
IC Inserts
Expected Hole Tolerances
Length
mm
in
Admissible Tightening Torque
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
ISO Material
D
Style
Part No.
Insert Screw
Torx® Driver
4T-030203C-P 4T-030203P-P 4T-030203C-M 4T-030203P-M 4T-030203C-H 4T-030203P-H 4T-030203C-K 4T-030203P-K 4T-030203C-N 4T-030203P-N
Center
P
BURNISHING
Periphery
Center
S M
Periphery
Center
0.5 N-m (4.4 in-lbs)
H
7241-T6-1
8T-6
Periphery
Center
K
Periphery
Center
N
Periphery
E
THREADING
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A55: 7
04
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Metric Shank 04 Series | Diameter Range: 13.50 mm - 15.49 mm (0.532" - 0.610")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Metric Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2041350M-20FM D2041400M-20FM D2040562I-20FM D2041450M-20FM D2041500M-20FM D3041350M-20FM D3041400M-20FM D3040562I-20FM D3041450M-20FM D3041500M-20FM D4041350M-20FM D4041400M-20FM D4040562I-20FM D4041450M-20FM D4041500M-20FM
13.50 14.00 14.29 14.50 15.00 13.50 14.00 14.29 14.50 15.00 13.50 14.00 14.29 14.50 15.00
0.531 0.551 0.563 0.571 0.591 0.531 0.551 0.563 0.571 0.591 0.531 0.551 0.563 0.571 0.591
27.00 28.00 28.55 29.00 30.00 40.50 42.00 42.82 43.50 45.00 54.00 56.00 57.10 58.00 60.00
48.40 49.40 49.40 50.40 51.40 61.90 63.40 63.40 64.90 66.40 75.40 77.40 77.40 79.40 81.40
91.40 92.40 92.40 93.40 94.40
20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00 20.00
27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00 27.00
0.50 0.40 0.30 0.30 0.20 0.50 0.40 0.30 0.30 0.20 0.50 0.40 0.30 0.30 0.20
2xD
104.90 106.40 106.40 107.90 109.40 118.40 120.40 120.40 122.40 124.40
3xD
C
REAMING
4xD
IC Inserts
Expected Hole Tolerances
D
Length
mm
in
BURNISHING ISO Material
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
P
4T-040203-P
S M 4T-040203-M H 4T-040203-H K 4T-040203-K N 4T-040203-N
0.5 N-m (4.4 in-lbs)
7241-T6-1
8T-6
E
THREADING
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
A55: 8
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
04
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Imperial Shank 04 Series | Diameter Range: 13.50 mm - 15.49 mm (0.532" - 0.610")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Imperial Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2041350M-075F D2041400M-075F D2040562I-075F D2041450M-075F D2041500M-075F D3041350M-075F D3041400M-075F D3040562I-075F D3041450M-075F D3041500M-075F D4041350M-075F D4041400M-075F D4040562I-075F D4041450M-075F D4041500M-075F
13.50 14.00 14.29 14.50 15.00 13.50 14.00 14.29 14.50 15.00 13.50 14.00 14.29 14.50 15.00
0.531 0.551 0.563 0.571 0.591 0.531 0.551 0.563 0.571 0.591 0.531 0.551 0.563 0.571 0.591
1.063 1.102 1.124 1.142 1.181 1.594 1.654 1.686 1.713 1.772 2.126 2.205 2.248 2.283 2.362
1.906 1.945 1.945 1.984 2.024 2.437 2.496 2.496 2.555 2.614 2.969 3.047 3.047 3.126 3.205
3.598 3.638 3.638 3.677 3.717 4.130 4.189 4.189 4.248 4.307 4.661 4.740 4.740 4.819 4.898
0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750 0.750
1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063 1.063
0.020 0.016 0.013 0.012 0.008 0.020 0.016 0.013 0.012 0.008 0.020 0.016 0.013 0.012 0.008
2xD
3xD
C
REAMING
4xD
IC Inserts
Expected Hole Tolerances
D
Length
mm
in
BURNISHING
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
P
4T-040203-P
S M 4T-040203-M H 4T-040203-H K 4T-040203-K N 4T-040203-N
0.5 N-m (4.4 in-lbs)
7241-T6-1
8T-6
E
THREADING
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A55: 9
05
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Metric Shank 05 Series | Diameter Range: 15.50 mm - 18.49 mm (0.611" - 0.728")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Metric Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2051550M-25FM D2050625I-25FM D2051600M-25FM D2051650M-25FM D2050656I-25FM D2051700M-25FM D2050687I-25FM D2051750M-25FM D2051800M-25FM D2050718I-25FM D3051550M-25FM D3050625I-25FM D3051600M-25FM D3051650M-25FM D3050656I-25FM D3051700M-25FM D3050687I-25FM D3051750M-25FM D3051800M-25FM D3050718I-25FM D4051550M-25FM D4050625I-25FM D4051600M-25FM D4051650M-25FM D4050656I-25FM D4051700M-25FM D4050687I-25FM D4051750M-25FM D4051800M-25FM D4050718I-25FM
15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24 15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24 15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24
0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718 0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718 0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718
31.00 31.75 32.00 33.00 33.32 34.00 34.90 35.00 36.00 36.47 46.50 47.63 48.00 49.50 49.98 51.00 52.35 52.50 54.00 54.71 62.00 63.50 64.00 66.00 66.64 68.00 69.80 70.00 72.00 72.95
54.50 54.50 55.50 56.50 56.49 57.50 57.50 58.50 59.50 59.51 70.00 70.00 71.50 73.00 73.00 74.50 74.50 76.00 77.50 77.50 85.50 85.50 87.50 89.50 89.51 91.50 91.50 93.50 95.50 95.50
108.50 108.50 109.50 110.50 110.50 111.50 111.50 112.50 113.50 113.51 124.00 124.00 125.50 127.00 127.00 128.50 128.50 130.00 131.50 131.50 139.50 139.50 141.50 143.50 143.51 145.50 145.50 147.50 149.50 149.50
25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 58.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00
32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00
0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.30 0.20 0.15 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.30 0.20 0.15 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.30 0.20 0.15
2xD
C
REAMING
3xD
D
BURNISHING
4xD
IC Inserts
Expected Hole Tolerances
Length
mm
in
E
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
THREADING
P
4T-05T203-P
S M 4T-05T203-M H 4T-05T203-H K 4T-05T203-K N 4T-05T203-N
0.5 N-m (4.4 in-lbs)
7243-T6-1
8T-6
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
A55: 10
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
05
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Imperial Shank 05 Series | Diameter Range: 15.50 mm - 18.49 mm (0.611" - 0.728")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Imperial Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2051550M-100F D2050625I-100F D2051600M-100F D2051650M-100F D2050656I-100F D2051700M-100F D2050687I-100F D2051750M-100F D2051800M-100F D2050718I-100F D3051550M-100F D3050625I-100F D3051600M-100F D3051650M-100F D3050656I-100F D3051700M-100F D3050687I-100F D3051750M-100F D3051800M-100F D3050718I-100F D4051550M-100F D4050625I-100F D4051600M-100F D4051650M-100F D4050656I-100F D4051700M-100F D4050687I-100F D4051750M-100F D4051800M-100F D4050718I-100F
15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24 15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24 15.50 15.88 16.00 16.50 16.66 17.00 17.46 17.50 18.00 18.24
0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718 0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718 0.610 0.625 0.630 0.650 0.656 0.669 0.687 0.689 0.709 0.718
1.220 1.250 1.260 1.299 1.312 1.339 1.374 1.378 1.417 1.436 1.831 1.875 1.890 1.949 1.968 2.008 2.061 2.067 2.126 2.154 2.441 2.500 2.520 2.598 2.624 2.677 2.748 2.756 2.835 2.872
2.146 2.146 2.185 2.224 2.224 2.264 2.264 2.303 2.343 2.343 2.756 2.756 2.815 2.874 2.784 2.933 2.933 2.992 3.051 3.051 3.366 3.366 3.445 3.524 3.524 3.602 3.602 3.681 3.760 3.760
4.272 4.272 4.311 4.350 4.350 4.390 4.390 4.429 4.469 4.469 4.882 4.882 4.941 5.000 5.000 5.059 5.059 5.118 5.177 5.177 5.492 5.492 5.571 5.650 5.650 5.728 5.728 5.807 5.886 5.886
1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000
1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260
0.031 0.029 0.028 0.020 0.016 0.016 0.012 0.012 0.008 0.006 0.031 0.029 0.028 0.020 0.016 0.016 0.012 0.012 0.008 0.006 0.031 0.029 0.028 0.020 0.016 0.016 0.012 0.012 0.008 0.006
2xD
C
REAMING
3xD
D
BURNISHING
4xD
IC Inserts
Expected Hole Tolerances
Length
mm
in
E
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
THREADING
P
4T-05T203-P
S M 4T-05T203-M H 4T-05T203-H K 4T-05T203-K N 4T-05T203-N
0.5 N-m (4.4 in-lbs)
7243-T6-1
8T-6
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A55: 11
06
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Metric Shank 06 Series | Diameter Range: 18.50 mm - 21.99 mm (0.728" - 0.866")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Metric Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2061850M-25FM D2061900M-25FM D2060750I-25FM D2060765I-25FM D2061950M-25FM D2062000M-25FM D2062050M-25FM D2060812I-25FM D2062100M-25FM D2062150M-25FM D3061850M-25FM D3061900M-25FM D3060750I-25FM D3060765I-25FM D3061950M-25FM D3062000M-25FM D3062050M-25FM D3060812I-25FM D3062100M-25FM D3062150M-25FM D4061850M-25FM D4061900M-25FM D4060750I-25FM D4060765I-25FM D4061950M-25FM D4062000M-25FM D4062050M-25FM D4060812I-25FM D4062100M-25FM D4062150M-25FM
18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50 18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50 18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50
0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846 0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846 0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846
37.00 38.00 38.10 38.86 39.00 40.00 41.00 41.25 42.00 43.00 55.00 57.00 57.15 58.29 58.50 60.00 61.50 61.87 63.00 64.50 74.00 76.00 76.20 77.72 78.00 80.00 82.00 82.49 84.00 86.00
58.40 59.40 59.40 59.41 60.40 61.40 62.40 62.40 63.40 64.40 76.90 78.40 78.40 78.41 79.90 81.40 82.90 82.90 84.40 85.90 95.40 97.40 97.40 97.41 99.40
112.40 113.40 113.40 113.41 114.40 115.40 116.40 116.40 117.40 118.40 130.90 132.40 132.40 132.41 133.90 135.40 136.90 136.90 138.40 139.90 149.40 151.40 151.40 151.41 153.40 155.40 157.40 157.40 159.40 161.40
25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00
32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00
0.90 0.80 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.20 0.90 0.80 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.20 0.90 0.80 0.80 0.70 0.70 0.50 0.40 0.40 0.30 0.20
2xD
C
REAMING
3xD
D
BURNISHING
4xD
101.40 103.40 103.40 105.40 107.40
IC Inserts
Expected Hole Tolerances
E
Length
mm
in
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
THREADING ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
P
4T-06T204-P
S M 4T-06T204-M H 4T-06T204-H K 4T-06T204-K N 4T-06T204-N
0.8 N-m (7.1 in-lbs)
72251-T7-1
8T-7
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
A55: 12
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
06
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Imperial Shank 06 Series | Diameter Range: 18.50 mm - 21.99 mm (0.728" - 0.866")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Imperial Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2061850M-100F D2061900M-100F D2060750I-100F D2060765I-100F D2061950M-100F D2062000M-100F D2062050M-100F D2060812I-100F D2062100M-100F D2062150M-100F D3061850M-100F D3061900M-100F D3060750I-100F D3060765I-100F D3061950M-100F D3062000M-100F D3062050M-100F D3060812I-100F D3062100M-100F D3062150M-100F D4061850M-100F D4061900M-100F D4060750I-100F D4060765I-100F D4061950M-100F D4062000M-100F D4062050M-100F D4060812I-100F D4062100M-100F D4062150M-100F
18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50 18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50 18.50 19.00 19.05 19.43 19.50 20.00 20.50 20.64 21.00 21.50
0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846 0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846 0.728 0.748 0.750 0.765 0.768 0.787 0.807 0.813 0.827 0.846
1.457 1.496 1.500 1.530 1.535 1.575 1.614 1.624 1.654 1.693 2.165 2.244 2.250 2.295 2.303 2.362 2.421 2.436 2.480 2.539 2.913 2.992 3.000 3.060 3.071 3.150 3.228 3.248 3.307 3.386
2.299 2.339 2.339 2.339 2.378 2.417 2.457 2.457 2.496 2.535 3.028 3.087 3.087 3.087 3.146 3.205 3.264 3.264 3.323 3.382 3.756 3.835 3.835 3.835 3.913 3.992 4.071 4.071 4.150 4.228
4.425 4.465 4.465 4.465 4.504 4.543 4.583 4.583 4.622 4.661 5.154 5.213 5.213 5.213 5.272 5.331 5.390 5.390 5.449 5.508 5.882 5.961 5.961 5.961 6.039 6.118 6.197 6.197 6.276 6.354
1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000
1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260
0.035 0.031 0.031 0.028 0.028 0.020 0.016 0.015 0.012 0.008 0.035 0.031 0.031 0.028 0.028 0.020 0.016 0.015 0.012 0.008 0.035 0.031 0.031 0.028 0.028 0.020 0.016 0.015 0.012 0.008
2xD
C
REAMING
3xD
D
BURNISHING
4xD
IC Inserts
Expected Hole Tolerances
E
Length
mm
in
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
THREADING
P
4T-06T204-P
S M 4T-06T204-M H 4T-06T204-H K 4T-06T204-K N 4T-06T204-N
0.8 N-m (7.1 in-lbs)
72251-T7-1
8T-7
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A55: 13
07
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Metric Shank 07 Series | Diameter Range: 22.00 mm - 26.49 mm (0.867" - 1.043")
A
L 1
L 3
DRILLING
L 2
D 1
D 2
D 3
Metric Shank
Body
Shank
D 1
B
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
D2072200M-25FM D2070875I-25FM D2072250M-25FM D2072300M-25FM D2072350M-25FM D2070937I-25FM D2072400M-25FM D2072450M-25FM D2072500M-25FM D2071000I-25FM D2072550M-25FM D2072600M-25FM D3072200M-25FM D3070875I-25FM D3072250M-25FM D3072300M-25FM D3072350M-25FM D3070937I-25FM D3072400M-25FM D3072450M-25FM D3072500M-25FM D3071000I-25FM D3072550M-25FM D3072600M-25FM D4072200M-25FM D4070875I-25FM D4072250M-25FM D4072300M-25FM D4072350M-25FM D4070937I-25FM D4072400M-25FM D4072450M-25FM D4072500M-25FM D4071000I-25FM D4072550M-25FM D4072600M-25FM
22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00 22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00 22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00
0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024 0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024 0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024
44.00 44.45 45.00 46.00 47.00 47.60 48.00 49.00 50.00 50.80 51.00 52.00 66.00 66.68 67.50 69.00 70.50 71.40 72.00 73.50 75.00 76.20 76.50 78.00 88.00 88.90 90.00 92.00 94.00 95.20 96.00 98.00
64.90 64.90 65.90 66.90 67.90 67.90 68.90 69.90 70.90 70.90 71.90 72.90 86.90 86.90 88.40 89.90 91.40 91.40 92.90 94.40 95.90 95.90 97.00 99.00
118.90 118.90 119.90 120.90 121.90 121.90 122.90 123.90 124.90 124.90 125.90 126.90 140.90 140.90 142.40 143.90 145.40 145.40 146.90 148.40 149.90 149.90 151.00 153.00 163.00 162.90 165.00 167.00 169.00 168.90 171.00 173.00 175.00 174.90 177.00 179.00
25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00 25.00
33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00 33.00
1.20 1.10 1.00 0.90 0.80 7.40 0.70 0.50 0.40 0.30 0.30 0.20 1.20 1.10 1.00 0.90 0.80 7.40 0.70 0.50 0.40 0.30 0.30 0.20 1.20 1.10 1.00 0.90 0.80 7.40 0.70 0.50 0.40 0.30 0.30 0.20
BORING
2xD
C
REAMING
3xD
D
109.00 108.90 111.00 113.00 115.00 114.90 117.00 119.00 121.00 120.90 123.00 125.00
BURNISHING
4xD
100.00 101.60 102.00 104.00
IC Inserts
Expected Hole Tolerances
E
Length
mm
in
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
THREADING ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
P
4T-070305-P
S M 4T-070305-M H 4T-070305-H K 4T-070305-K N 4T-070305-N
1.2 N-m (10.6 in-lbs)
72568-T8-1
8T-8
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
A55: 14
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
07
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Imperial Shank 07 Series | Diameter Range: 22.00 mm - 26.49 mm (0.867" - 1.043")
A
L 1
L 3
DRILLING
L 2
D 1
D 2
D 3
Imperial Shank
Body
Shank
D 1
B
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
D2072200M-100F D2070875I-100F D2072250M-100F D2072300M-100F D2072350M-100F D2070937I-100F D2072400M-100F D2072450M-100F D2072500M-100F D2071000I-100F D2072550M-100F D2072600M-100F D3072200M-100F D3070875I-100F D3072250M-100F D3072300M-100F D3072350M-100F D3070937I-100F D3072400M-100F D3072450M-100F D3072500M-100F D3071000I-100F D3072550M-100F D3072600M-100F D4072200M-100F D4070875I-100F D4072250M-100F D4072300M-100F D4072350M-100F D4070937I-100F D4072400M-100F D4072450M-100F D4072500M-100F D4071000I-100F D4072550M-100F D4072600M-100F
22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00 22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00 22.00 22.22 22.50 23.00 23.50 23.81 24.00 24.50 25.00 25.40 25.50 26.00
0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024 0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024 0.866 0.875 0.886 0.906 0.925 0.937 0.945 0.965 0.984 1.000 1.004 1.024
1.732 1.750 1.772 1.811 1.850 1.874 1.890 1.929 1.969 2.000 2.008 2.047 2.598 2.625 2.657 2.717 2.776 2.811 2.835 2.894 2.953 3.000 3.012 3.071 3.465 3.500 3.543 3.622 3.701 3.748 3.780 3.858 3.937 4.000 4.016 4.094
2.555 2.555 2.594 2.634 2.673 2.673 2.713 2.752 2.791 2.791 2.831 2.870 3.421 3.421 3.480 3.539 3.598 3.598 3.657 3.717 3.776 3.776 3.835 3.894 4.287 4.287 4.366 4.445 4.524 4.524 4.602 4.681 4.760 4.760 4.839 4.917
4.681 4.681 4.720 4.760 4.799 4.799 4.839 4.878 4.917 4.917 4.957 4.996 5.547 5.547 5.606 5.665 5.724 5.724 5.783 5.843 5.902 5.902 5.961 6.020 6.413 6.413 6.492 6.571 6.650 6.650 6.728 6.807 6.886 6.886 6.965 7.043
1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000
1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299 1.299
0.047 0.043 0.039 0.035 0.031 0.292 0.028 0.020 0.016 0.013 0.012 0.008 0.047 0.043 0.039 0.035 0.031 0.292 0.028 0.020 0.016 0.013 0.012 0.008 0.047 0.043 0.039 0.035 0.031 0.292 0.028 0.020 0.016 0.013 0.012 0.008
BORING
2xD
C
REAMING
3xD
D
BURNISHING
4xD
IC Inserts
Expected Hole Tolerances
E
Length
mm
in
2xD 3xD 4xD
-0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.20 -0.004 / +0.008 -0.10 / +0.25 -0.004 / +0.010
THREADING
ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
P
4T-070305-P
S M 4T-070305-M H 4T-070305-H K 4T-070305-K N 4T-070305-N
1.2 N-m (10.6 in-lbs)
72568-T8-1
8T-8
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A55: 15
09
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Metric Shank 09 Series | Diameter Range: 26.50 mm - 31.99 mm (1.044" - 1.259")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Metric Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2092650M-32FM D2092700M-32FM D2092750M-32FM D2092800M-32FM D2092850M-32FM D2091125I-32FM D2092900M-32FM D2092950M-32FM D2093000M-32FM D2091187I-32FM D2093050M-32FM D2093100M-32FM D2093150M-32FM D2091250I-32FM D3092650M-32FM D3092700M-32FM D3092750M-32FM D3092800M-32FM D3092850M-32FM D3091125I-32FM D3092900M-32FM D3092950M-32FM D3093000M-32FM D3091187I-32FM D3093050M-32FM D3093100M-32FM D3093150M-32FM D3091250I-32FM
26.50 27.00 27.50 28.00 28.50 28.58 29.00 29.50 30.00 30.15 30.50 31.00 31.50 31.75 26.50 27.00 27.50 28.00 28.50 28.58 29.00 29.50 30.00 30.15 30.50 31.00 31.50 31.75
1.043 1.063 1.083 1.102 1.122 1.125 1.142 1.161 1.181 1.187 1.201 1.220 1.240 1.250 1.043 1.063 1.083 1.102 1.122 1.125 1.142 1.161 1.181 1.187 1.201 1.220 1.240 1.250
53.00 54.00 55.00 56.00 57.00 57.15 58.00 59.00 60.00 60.30 61.00 62.00 63.00 63.50 79.50 81.00 82.50 84.00 85.50 85.73 87.00 88.50 90.00 90.45 91.50 93.00 94.50 95.25
75.70 76.70 77.70 78.70 79.70 79.70 80.70 81.70 82.70 82.70 83.70 84.70 85.70 85.70
134.70 135.70 136.70 137.70 138.70 138.70 139.70 140.70 141.70 141.70 142.70 143.70 144.70 144.70 161.20 162.70 164.20 165.70 167.20 167.20 168.70 170.20 171.70 171.70 173.20 174.70 176.20 176.20
32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00
41.00 41.00 41.00 41.00 41.00 41.00 41.00 43.00 43.00 43.00 43.00 43.00 43.00 43.00 41.00 41.00 41.00 41.00 41.00 41.00 41.00 43.00 43.00 43.00 43.00 43.00 43.00 43.00
1.68 1.60 1.45 1.30 1.21 1.20 1.10 0.97 0.80 0.82 0.74 0.60 0.50 0.50 1.68 1.60 1.45 1.30 1.21 1.20 1.10 0.97 0.80 0.82 0.74 0.60 0.50 0.50
2xD
C
REAMING
102.20 103.70 105.20 106.70 108.20 108.20 109.70 111.20 112.70 112.70 114.20 115.70 117.00 117.20
3xD
D
BURNISHING
IC Inserts
Expected Hole Tolerances
Length
mm
in
2xD 3xD 4xD
-0.15 / +0.25 -0.006 / +0.010 -0.15 / +0.25 -0.006 / +0.010 -0.15 / +0.30 -0.006 / +0.012
E
ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
P
4T-09T306-P
THREADING
S M 4T-09T306-M H 4T-09T306-H K 4T-09T306-K N 4T-09T306-N
2.0 N-m (17.7 in-lbs)
738-T10-1
8T-10
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
A55: 16
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
09
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Metric Shank 09 Series | Diameter Range: 26.50 mm - 31.99 mm (1.044" - 1.259")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Metric Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D4092650M-32FM D4092700M-32FM D4092750M-32FM D4092800M-32FM D4092850M-32FM D4091125I-32FM D4092900M-32FM D4092950M-32FM D4093000M-32FM D4091187I-32FM D4093050M-32FM D4093100M-32FM D4093150M-32FM D4091250I-32FM
26.50 27.00 27.50 28.00 28.50 28.58 29.00 29.50 30.00 30.15 30.50 31.00 31.50 31.75
1.043 1.063 1.083 1.102 1.122 1.125 1.142 1.161 1.181 1.187 1.201 1.220 1.240 1.250
106.00 108.00 110.00 112.00 114.00 114.30 116.00 118.00 120.00 120.60 122.00 124.00 126.00 127.00
128.70 130.70 132.70 134.70 136.70 136.70 138.70 140.70 142.70 142.70 144.70 146.70 148.70 148.70
187.70 189.70 191.70 193.70 195.70 195.70 197.70 199.70 201.70 201.70 203.70 205.70 207.70 207.70
32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00 32.00
41.00 41.00 41.00 41.00 41.00 41.00 41.00 43.00 43.00 43.00 43.00 43.00 43.00 43.00
1.68 1.60 1.45 1.30 1.21 1.20 1.10 0.97 0.80 0.82 0.74 0.60 0.50 0.50
4xD
C
REAMING
D
BURNISHING
IC Inserts
Expected Hole Tolerances
Length
mm
in
2xD 3xD 4xD
-0.15 / +0.25 -0.006 / +0.010 -0.15 / +0.25 -0.006 / +0.010 -0.15 / +0.30 -0.006 / +0.012
E
ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
P
4T-09T306-P
THREADING
S M 4T-09T306-M H 4T-09T306-H K 4T-09T306-K N 4T-09T306-N
2.0 N-m (17.7 in-lbs)
738-T10-1
8T-10
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
A55: 17
09
DRILLING | 4TEX® Drill: Indexable Carbide Insert Drilling System
4TEX Drill Holders | Imperial Shank 09 Series | Diameter Range: 26.50 mm - 31.99 mm (1.044" - 1.259")
A
L 1
DRILLING
L 3
L 2
D 1
D 2
D 3
Imperial Shank
B
Body
Shank
D 1
Length
mm
in
Max Offset
Part No.
L 2
L 3
L 1
D 2
D 3
BORING
D2092650M-125F D2092700M-125F D2092750M-125F D2092800M-125F D2092850M-125F D2091125I-125F D2092900M-125F D2092950M-125F D2093000M-125F D2091187I-125F D2093050M-125F D2093100M-125F D2093150M-125F D2091250I-125F D3092650M-125F D3092700M-125F D3092750M-125F D3092800M-125F D3092850M-125F D3091125I-125F D3092900M-125F D3092950M-125F D3093000M-125F D3091187I-125F D3093050M-125F D3093100M-125F D3093150M-125F D3091250I-125F
26.50 27.00 27.50 28.00 28.50 28.58 29.00 29.50 30.00 30.15 30.50 31.00 31.50 31.75 26.50 27.00 27.50 28.00 28.50 28.58 29.00 29.50 30.00 30.15 30.50 31.00 31.50 31.75
1.043 1.063 1.083 1.102 1.122 1.125 1.142 1.161 1.181 1.187 1.201 1.220 1.240 1.250 1.043 1.063 1.083 1.102 1.122 1.125 1.142 1.161 1.181 1.187 1.201 1.220 1.240 1.250
2.087 2.126 2.165 2.205 2.244 2.250 2.283 2.323 2.362 2.374 2.402 2.441 2.480 2.500 3.130 3.189 3.248 3.307 3.366 3.375 3.425 3.484 3.543 3.561 3.602 3.661 3.720 3.750
2.980 3.020 3.059 3.098 3.138 3.138 3.177 3.217 3.256 3.256 3.295 3.335 3.374 3.374 4.024 4.083 4.142 4.201 4.260 4.260 4.319 4.378 4.437 4.437 4.496 4.555 4.614 4.614
5.303 5.343 5.382 5.421 5.461 5.461 5.500 5.539 5.579 5.579 5.618 5.657 5.697 5.697 6.346 6.406 6.465 6.524 6.583 6.583 6.642 6.701 6.760 6.760 6.819 6.878 6.937 6.937
1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250
1.614 1.614 1.614 1.614 1.614 1.614 1.614 1.693 1.693 1.693 1.693 1.693 1.693 1.693 1.614 1.614 1.614 1.614 1.614 1.614 1.614 1.693 1.693 1.693 1.693 1.693 1.693 1.693
0.066 0.063 0.057 0.051 0.048 0.046 0.043 0.038 0.031 0.032 0.029 0.024 0.020 0.019 0.066 0.063 0.057 0.051 0.048 0.046 0.043 0.038 0.031 0.032 0.029 0.024 0.020 0.019
2xD
C
REAMING
D
3xD
BURNISHING
IC Inserts
Expected Hole Tolerances
Length
mm
in
E
2xD 3xD 4xD
-0.15 / +0.25 -0.006 / +0.010 -0.15 / +0.25 -0.006 / +0.010 -0.15 / +0.30 -0.006 / +0.012
ISO Material
Admissible Tightening Torque
Part No.
Insert Screw
Torx® Driver
P
4T-09T306-P
THREADING
S M 4T-09T306-M H 4T-09T306-H K 4T-09T306-K N 4T-09T306-N
2.0 N-m (17.7 in-lbs)
738-T10-1
8T-10
X
A55: 32 - 33
A55: 29 - 31
A55: 28
SPECIALS
= Metric (mm) = Imperial (in)
Key on A55: 1
IC inserts sold in quantities of 10 Insert screws sold in quantities of 10
A55: 18
www.alliedmachine.com | +44 (0) 1384 400 900 | enquiries.eu@alliedmachine.com
Made with FlippingBook Digital Publishing Software